3 Ways to Polish Polyurethane - wikiHow (2024)

Explore this Article

Co-authored bySam Hubbardand Janice Tieperman

Last Updated: September 20, 2023References

Download Article

1. 1

   Spritz over the finished surface with tap water. After you’ve applied your polyurethane and let it dry completely, fill a plastic spray bottle with cool tap water. Lightly mist the surface with water so you can sand down the finish more efficiently.^[1]

   • When working with polyurethane, wet sanding is the best way to ensure a smooth finish.
2. 2

   Use an orbital sander and 2000-grit paper to buff the wet surface. Take a circular sheet of smooth sandpaper and fit it into your sander. Turn the machine to a low power setting, then rub the sander in slow, horizontal motions across the surface. Apply a light, even amount of pressure so you can work away any scratches or bumps in the finish. Start on 1 side of the surface, then move the sander slowly to the opposite side.^[2]

   • Make sure that the sandpaper is labeled as “wet/dry.” You can find this type of paper at most hardware or home improvement stores, or you can buy it online.

   Tip: You can also use a scrubbing pad with your orbital sander. Without inserting any sandpaper or buffing pads, rest the blank surface of the sander on top of the scrubbing pad. Once you turn your sander on to a low speed, the pad will spin and buff the finished surface. For a shinier finish, stick a soft buffing pad beneath your sander instead.^[3]

   Advertisem*nt

3. 3

   Sand down the surface by hand if you don’t have a handheld tool. Use a smooth piece of sandpaper that’s around 1500-grit, then start rubbing down the finish in long, smooth motions. If you don’t have any sandpaper on hand, you can also use a brown paper bag to buff the surface.^[4]

   • If you don’t have any super-fine sandpaper on hand, you can use a lower grit level, like 320.^[5]
   • You may have an easier time sanding by hand if you wrap the sandpaper around a block of styrofoam.
4. 4

   Wipe any residue from the surface with a clean cloth. As you buff the surface of your finish, look for any dust or slurry building up on the surface. When you see this residue, use a clean cloth to wipe and remove it from the surface gently.^[6]

   • Sanding polyurethane can be a time-consuming process, so you may have to do this several times.
5. 5

   See Also

   How Long Does Polyurethane Take To Dry? - Today's Homeowner*How Do I Remove Brush Strokes from the 3rd Coat of High Performance Polyurethane? | General Finishessunlight curing for poly?HOW SOON AFTER MY HARDWOOD FLOORS ARE FINISHED CAN I ... ??? — Valenti Flooring

   Repeat the spraying and sanding process until the surface feels smooth. Feel the surface of your polyurethane to see if the bumps and scratches are gone. If not, continue buffing in long, slow motions along the sides and edges of the surface. Try to go extra slowly and light along the edges so you don’t sand through the finish by mistake.^[7]

   • Switch out your sandpaper pad if it looks dirty or clogged with polyurethane slurry.^[8]
   • This process may take several minutes to complete. Don’t be discouraged if you don’t see results right away!

Advertisem*nt

Download Article

1. 1

   Insert a foam buffing pad in your orbital sander. Remove the sandpaper pad and replace it with a 1in (2.5cm) thick foam insert. If you’re having trouble switching or installing a new pad, consult your user manual for advice.^[9]

2. 2

   Spread a grape-sized amount of car polish onto the pad. Try to coat a good portion of the foam pad, then smear the polish on top of the finish. Make sure that the polish is clear, and not designed for dark exteriors.^[10]

   • You can buy car polish online, or in an auto supply shop.
   • Feel free to use more or less polish, depending on the size of your project.
3. 3

   Buff the polish into the finished project until the surface looks shiny. Turn your orbital sander onto a low speed and apply a small amount of pressure to the finished surface.^[11] Work in long, horizontal motions to work the polish into the polyurethane.^[12]

   • Don’t be discouraged if the surface doesn’t look shiny right away. It’ll take a few minutes before the polish is completely buffed in.
   • Be careful when you polish around the edges, as you don’t want to burn through the polyurethane.
4. 4

   Use a polishing cloth to buff any residue into the surface. Rub the cloth in wide, circular motions along the entire finish. Continue wiping down the surface until it looks glossy and reflective.^[13]

   • This helps to get rid of any excess polish stuck to the surface.
5. 5

   Rub a swirl mark remover onto the surface with a polishing cloth. Pour a blueberry-sized amount of automotive swirl mark remover onto a soft, clean polishing cloth, then wipe down the polished surface with circular motions. Once you’ve coated the entire surface, use another cloth to wipe off any excess.^[14]

   • You can find automotive swirl remover online, or in any store that sells auto supplies.

   Tip: Glossy finishes are a great option for eye-catching items, like a coffee table or acoustic guitar.^[15]

Advertisem*nt

Download Article

1. 1

   Rub the wax in the same direction as the grain. Add a pea-sized amount of car paste wax to a polishing pad or cloth. Work in short, smooth motions until there are no visible scratches in the polyurethane.^[16] Move the pad in smooth, horizontal motions so you can apply an even coat of wax to the surface.^[17]

   • You can also use a section of 0000 steel wool to buff the surface.^[18]
   • To make things easier, apply wax to the end sections of the wood first. Always follow the grain when you do this!
   • For a more careful polishing job, use short, smooth strokes as you go.
2. 2

   Use a paper shop towel to clean off any excess wax. Before the paste wax has a chance to dry, use a sheet of paper shop towel to rub and get rid of any residue. Go over the entire surface with the towel in long, horizontal motions, picking up any leftover wax as you go.^[19]

   • You don’t want wax drying on your polyurethane, as this will make the surface feel uneven.
3. 3

   Spray and rub down the surface with water if any wax dries. Sprinkle a few droplets of tap water over the entire waxed surface, which will bead on the surface of your waxed finish. Use a clean, 0000 steel wool pad to brush down the surface lightly from left to right. Once you’ve given the finish a good wipe, flip the pad and repeat the wiping process. Once you’ve gotten rid of any leftover wax, blot away the water with a cloth or paper towel.^[20]

   Tip: Satin finishes are great for functional items, like kitchen tables.^[21]

Advertisem*nt

Expert Q&A

Ask a Question

Video.

By using this service, some information may be shared with YouTube.

Thanks for submitting a tip for review!

Warning

Things You’ll Need

Buffing the Finished Surface

Using Polish for a Glossy Surface

Waxing for a Satin Surface

How helpful is this?